Strobotics

The other day while playing around with the ADC on the widget I had some problems with noise causing the reading to bounce around, It needed some form filtering to remove the noise.   Normally almost everyone seems to take a number of readings and then average the result, unfortunately this takes time.

I came across this simple low pass filter on EDN.  A Low pass filter works by blocking the higher frequency (in this case noise) and allowing the low frequency signal (in this case the underlying signal) to pass. hence the name.  Perfect in cases where measuring slow moving signals, like temperature etc.  The algorithm is fast, simple to implement and works a treats.  It can be made to filter faster for a more response to change or slower to give more filtering.

#define FILTER_SHIFT 3

int32_t filter_reg;

int16_t filter_input;

int16_t filter_output;

filter_input = analogRead(0);                 // read ADC

// low pass filter to get rid of noise

filter_reg = filter_reg - (filter_reg >> FILTER_SHIFT) + filter_input; 

filter_output = filter_reg >> FILTER_SHIFT;   

The algorithm is a classified as a leaky integrator, where the latest reading have more weight than the older reading.  So you take a single reading each cycle of the sensor loop and feed that into the filter, the output is used you would normally use the raw value.

The response of the filer can be adjusted by the FILTER_SHIFT, to make it more responsive, then lower this value, to give better filtering and hence a slower response then increase this value.  For my application I found that a value of 3 to 4 worked well, but will depend on the underlying application.

I suggest you read the full article for an in depth description.

In my previous blog entry I described adding a solar cell to the widget and how I could measure the voltage produced by the Solar Cell, however I still need to monitor actual battery voltage easily, and preferably with not a lot of additional hardware.

Problems reading ones own voltage.

Measuring ones own voltage has a couple of problems:

1. You can’t just measure VCC directly, i.e. you can’t connect an analog pin to VCC.  The reason is the battery voltage varies, and since the default AREF is tied to VCC you will always read VCC unless you use some form of a reference not tied to VCC.

2. I can also use a reference diode and a resistor between VCC and GND, to form an external reference voltage, the diode has a known voltage drop across it so this can be measured using the default AREF.  We can calculate the battery voltage by measuring the volt drop across the diode.  While this will work, the circuit will always consume a small amount of power, even when not being used, remember I want to get as much life out of my batteries as possible.  So it rules this out as a solution.

3. For the same reasons as 1) I can’t use a simple voltage divider and the default AREF.  As the voltage varies so too will my readings.

4. I can use a simple voltage divider and the internal 1.1v bandgap reference for my AREF, the same as I used for my solar cell voltage monitor in the previous blog entry.  Again this will work, but also as in 2) this will always consume  some power even when not being used, so is ruled out as a solution in this case.

No Extra components?

We can however measure VCC voltage with no external components by simply reading the value of the internal bandgap reference voltage (1.1v) which is always fixed regardless of the battery voltage,  and by using the default AREF which is tied to VCC, so will vary as the battery voltage changes.  We now have a way of measuring the voltage change against a fixed reference.

V_BAT =  (VREF * 1024) / analogRead(14);

Where:

You might see in the above formula, that analogRead() function is reading channel 14.  But analogRead() only supports channels 0-7 right? 

Correct, but what we are doing is to read the internal ADC channels after we make a small change to the Arduino source code.

Changes to “wiring_analog.c”

To take an ADC measurement of  the internal bandgap we need to switch to ADC MUX channel 14 (23.8.1 in reference manual).   However to do this with the arduino wiring library we need to make changes to “wiring_analog.c” as per http://code.google.com/p/arduino/issues/detail?id=10.  This change allows us to read from all ADC MUX channels, internal and external.

Example

Once you’ve made the change to “wiring_analog.c” then use the following example sketch to read your VCC/Battery Voltage.

uint16_t raw_bandgap = 0;      // Internal bandgap reference

float volt_battery = 0.0;

void setup(){

  Serial.begin(57600);

}

void loop(){

  // Read Battery voltage

  analogReference(DEFAULT);                          // use VCC as AREF

  raw_bandgap = analogRead(14);                      // read and discard first result after changing reference (see 23.5.2 of manual)

  raw_bandgap = analogRead(14);                      // measure internal bandgap voltage

  volt_battery = (1.1 * 1024) / raw_bandgap;         // calculate voltage

  Serial.print(volt_battery);

  Serial.println(" v_bat");

  delay(1000);                    

}

When this method won’t work.

If you have a voltage regulator or a protection diode inline between your battery and VCC, then this will only show the voltage at VCC, not the true battery voltage. 

If you have a voltage regulator then you will always read what it puts out, and not give a true indication of battery voltage.  I guess you could still use the method as a form of low battery measurement.  i.e. when the battery falls below regulation values I guess the regulator will fail to regulate and you should get a lower than normal reading.  however I haven’t tested this theory.

If you only have a protection Diode then measure the volt drop across it and compensate in your calculations, it will still give you a good indication of battery voltage.

Update:

Some other uses for this method is for auto-calibration of sensors as described by ladyada(you need to go to the bottom of the page)

One of the tasks I want to use the widget boards for is a Wireless Sensor Network around the house for measuring environmental values.  The sensors that I want to live outdoors will need to be self sufficient in terms of power, so I wanted to see if I could charge the batteries via solar, of course this can be done, but again I want to do it as cheaply and as simply as possible, I also want the widget board to monitor the solar voltage and report it back.

I already had a 3.6v 0.2w cell that I picked up some time ago from Sure Electronics for about $10 for 5.  The spec for this cell is max voltage (under load) is 3.6v and max current is 60mA, more than enough to trickle charge x2 AA NIMH batteries. 

The Batteries should not require much of a top up as the node will be sleeping most of the time, from the power saving discussion @ JEELabs, by adding the solar, I should be able to just leave the node without having to change batteries (replacing failed batteries aside).

To measure the voltage produced by the solar cell I need a voltage divider that would produce 1.1v max @ 3.6v.

Why 1.1v I hear you ask?  The reason for the A/D full scale input voltage of 1.1V is that I’ll be using the ATMega168 internal bandgap reference as the AREF source for the onboard A/D and not the default AREF. 

There are a couple for reasons for this.  The internal bandap reference itself is a 1.1v voltage reference, because the battery voltage may change over time (remember I’m not using any onboard voltage regulators) so as the VCC / battery voltage changes, so would my A/D voltage readings unless I use a reference voltage.   Now as the reference is 1.1v this means that my input must not go above 1.1v else I will go over scale and get an incorrect reading.

I’m not going to bore you with the math so a quick calculation using an online voltage divider calculator (http://www.daycounter.com/Calculators/Voltage-Divider-Calculator.phtml)

Input Voltage = 3.6v

Output Voltage = 1.0v  (remember I don’t want to go over 1.1V so I’ve given myself some headroom)

Gave the values for R1 = 26K and R2 = 10K

Luckily I had both these values, however for the 26K I only had  one in 5% tolerance, the 10K I had as 1% (I like to use low tolerance resistors for voltage dividers so my error is minimised),upon testing the 26K resistor actually read 26.4K on my meter, so after plugging these real values in my actual FS Vout is 0.989v, pretty close to 1.0V.

A blocking diode is also required to prevent any damage to the Solar cell by the batteries, see the circuit and photo below.

(Click for larger image)

(Click for larger image and notes)

Arduino Sketch to read the voltage produced by the solar cell, next step is to find a waterproof housing and add some environmental sensors. 

Another benefit of taking voltage readings of the solar cell is I now have a light sensor.

int raw_solar = 0;        // Raw Solar FS ~ 1.0v

int raw_bandgap = 0;      // Intenal bandgap reference

float volt_solar = 0.0;

void setup(){

  Serial.begin(57600);

  analogReference(INTERNAL);  // select internal reference for AREF

}

void loop(){

  raw_solar = analogRead(0);                         // read solar voltage raw values

  volt_solar = (raw_solar * 1.1 * 3.617) / 1024;     // Scale ADC input.  (voltage divider r1= 26.4k  r2 = 10k  vi=vo/(r2/(r1+r2)) = vo/.2777 =  vo * 3.617

  Serial.print(volt_solar);                          // display raw solar voltage reading

  Serial.println("v");  

  delay(1000);                    

}

The other day when playing around with different fuse settings on the Widget Board, I incorrectly wrote the wrong values, oops one bricked board   However all is not lost.

With a second working Widget Board and a simple Arduino sketch , I used the following procedure to recover from my mishap.

First I installed the following sketch onto a working Widget Board

void setup() {

  pinMode(3, OUTPUT);  

}

void loop() {

  while(1) {

    PIND |= _BV(3);

  }

}

What this sketch does is generate a 1.2MHz clock signal on the INT1 port of the Widget Board. (Click the picture below to see the the full trace )

Next I attached this signal to the XTAL1 pin (Pin 7) of the AtMega168v on the bricked board (I just held it against the crystal pin). 

While holding this connection on the pin, I then fired up AVR-DUDE and rewrote the correct fuse settings, after confirming that the fuse values could be read back I then remove the wire and everything was back to normal.

So all is not lost

I had a chance to grab a few photos of the progress so far, also helps that most of my components that I had on order arrived today so the boards has been kitted out with all the headers.  Now I can plug the prototype personality in, still waiting on my crystals, switches, and diodes.

This gives an idea of size. (I don’t have big hands either)  This board has a 900MHz 2dB GSM SMA antenna, prototype personality board installed and battery holder for CR123A Lithium battery. 

Different battery options, using x2AA with a switched battery pack soldered onto the board.

The SMA connector is a standard PCB straight SMA connector that has been soldered onto the edge of the board.  The board have been designed for the Sparkfun PCB edge mounted SMA connector (SKU: WRL-00593), however I found that a standard PCB SMA connector will do the same job, the distance between the centre pin and the ground pins is the same thickness as the PCB and all the pins line up with the Sparkfun footprint, the centre pin fits perfectly and so do the two bottom ground pins, only difference is the two top ground pins don’t get soldered.

One of the LEDs flashing….Its Alive!!!!

Today I did some testing on the RF side of things,  nothing scientific, just walking around the house seeing if it would dropout or report bad checksums, I’m happy to reports all is working as expected (using the 915Mhz RFM12B module)

The tests are done by using the RFM12B Example sketch found in the JeeLab RFM12B library by Jean-Claude over at Jeelab (RFM12B Arduino Library)

This library runs unmodified on the wireless widget board, just follow the instructions in the README about setting up node ids.

From the preliminary testing using some compact 1/2 wave GSM 900MHZ/1800MHZ antennas (http://www.dealextreme.com/details.dx/sku.5237)  I’m easily getting all the way around the house with no dropouts, have yet to do outside tests.

Today I constructed another 2 boards, very easy to do all done in around 30 minutes.  This now brings the total to 3.

Applying the boards with solder paste by hand, manually placing the components, bake them in the toaster oven together.  This time I got the LEDs the right way around and the right amount of solder paste on everything, no bridges on the CPU pins and looks like the right amount of fillet on the RFM12B module, very little cleanup work required, it’s amazing how little solder paste is required.

Add another 5 minutes to hand solder on the SMA connectors and program the boot loader on each, voila all done in around 30 minutes.

Now I have a potential “Network” I will start testing the RF side of things.  Currently I’m using the 915MHz modules.

Today I got a chance to do some testing on the boards. 

State of play so far:

1. Checked for shorts on power – OK
2. Did a board level continuity test – everything as per schematic.
3. Power at the correct levels and at the right places.
4. Found that my USBASP programmer needs sw2 set and now all working, I can now read and set fuses etc.
5. Arduino lillypad bootloader successfully loaded and working – Whoot!
6. ASCII sketch loaded via Arduino development environment, serial port tested at 9600, all working.
7. Jean claudes RFM12B Test Sketch loaded and working.  Can configure device and some random data is being read back from RFM12B, need a second board operational to fully test the RF side of things.

TODO:

1. Build a second device now that the basic circuit is working and verified.
2. Fully test RFM12B and wireless comms.
3. Test I/O i.e. Analogue and Digital ports, LEDS  etc
4. Customise boot loader to use onboard LEDS.
5. Document all of the above for others on the project’s website.

All in all I’m pretty happy

Ok here is the 1st basic trigger personality board.

Features:

• x4 LEDs for visual indication.
• x2 Push Button Switches, one tied to input for manual triggering/testing, the second independent, could be used for channel or function selection, both could used in conjunction with LEDS for advanced function selection.
• 1 Strobe output. 400V Max (so will work with older type strobes)
• 1 protected TTL trigger input. 
• Small prototype area.
• Low profile, All large components are mounted underneath.

Still a little cleaning up required but basic functionality is there.

Still TO DO:

• Change MOC3023 to SMD footprint, I don’t really want the possibility of a large strobe voltage right where a thumb might be.

Basic Triggr Personality PCB

For those interested I found an RFM12 library for the Arduino  http://jeelab.equi4.com/2009/02/10/rfm12b-library-for-arduino/

I’ve been playing around with the Arduino Diecimila and the ATMEGA168 over the last couple of weeks to better familiarise myself with the AVR ATMega168 MCU, I’ve been using PICs on and off the last few years, but the decision was made to use the ATMEGA as the MCU of choice for the Strobit Triggr project, mainly due to the open source tool chains available, and the simply programmer required.

In short I’m glad I’ve made the switch and I must say I’m loving the learning experience.  I’ve moved from the Arduino software development platform as I found it very limiting and am now using the open source avr-gcc (win-avr) and Eclipse, using the AVR plugin and CDT plugin as my development platform of choice, I’m comfortable with eclipse as my editor as I’ve been using this for my Java development for the last 5 or so years.

As a task I set for myself to learn the onboard peripherals,  I’ve created a Weather Shield for the Arduino, so far it has the RFM12B RF module, DS1307 RTC, HH10D Humidity Sensor, a HP03D, combined barometric pressure and temperature sensor, and soon to have a light sensor and Dallas 1-Wire interface for talking to the Dallas Weather Station that I’ve had lying around in a box for the last 10 years, (yes one of the original ones released by Dallas in 1998, I’ve been waiting to move in my house for a long time),  I’ll post the weather shield design up on a separate topic later, but suffice to say, I’ve enjoyed playing with the SPI, I2C, ICP, UART and onboard timers.