Strobotics

My sample order of the RFM22 were waiting for me when I arrived home late last night.

Here is a picture of the RFM22 (Left) next to the RFM12B (Right).  Pretty much the same physical size, but more pins, and a lot of very small discrete components.

So What’s New?

These new transceiver modules from HopeRF appear to be based on Silicon Labs Si4431 and Si4432 RF Chips.  Silicon Labs purchased Integration, from where the RFM12B were based on their EzRadio Series of transceiver chips.

It looks like there are a heap of new feature available, (too many to list here), including some onboard lower MAC smarts called EzyMac, while not as nice as the 802.15.4 MAC layer it looks like it can simplify things such as:

• Automatically adding pre-amble and sync bytes.
• Automatic packet size – you just push bytes into the Tx FIFO and it will create the packets of a fixed size and send for you.
• Built in basic frequency hopping.
• Built in Data Whitening, Manchester Encoding, and CRC

Some more niceties:

• 64Byte FIFO.
• Onboard A/D, allows access to read such things as an onboard Temperature Sensors, Voltage buses.
• x2 configurable GPIO ports.
• More Rx Sensitivity than the RFM12B.
• More Tx power than the RFM12B
• Lower Operating voltage.
• 8bit RSSI value.
• Three different modulation schemes to select from.

Some not so niceties:

• More current draw on Rx than the RFM12B.
• More current draw on Tx than the RFM12B (understandable seeing it also has a higher Tx Power).
• Costs about twice as much as the RFM12B ~ $USD6.00 in sample quantities direct from HopeRf vs ~$USD3.00 for the RFM12B.
• Heaps more commands/Registers to learn.
• No onboard encryption.

Feature comparison:

Hmm Its been a while since I revisited the RFM12 tutorials, so I thought I’d better write the next one.  Unfortunately it’s going to be too long to fit in one post so I’ll be splitting it across a couple of posts.

The last two tutorials covered a brief introduction and the physical connection to the MCU.  In this article I’m going to cover the internal commands and how we go about controlling to the RFM12 module.

It’s all done with Smoke and Mirrors!

Well not really, I wish it were that simple…as mentioned previously that the RFM12 needs to be connected as described in the previous article via SPI, the second thing we need to do is access the the internal registers of the RFM12 for it to be useful.

The SPI transfers 16-bit commands to the RFM12, as part of the SPI transfer process it will receive results (if any) back to the MCU.  These commands do specific things, such as set the band, turn on the Transmitter and so on, therefore to get an understanding of what we need to do, we need to understand what the various commands do.

It also helps if you to have the RFM12 data sheet open as go through this as I’ll be explaining  things in roughly the same order as found on the current data sheet, most of this information is direct out of the datasheet.

SPI Interface

Just before we go through the commands, we need to be able to talk to the RFM12, and seeing that we have the SPI and NSEL correctly setup as described in Part 2 we need some routines to talk to the RFM12 and it’s registers.

There are basically two ways to do this, 1) Bit banging the SPI or  2) using on-board hardware SPI peripheral.  The Hope RF programming guide offers a solution to bit banging the SPI interface so I won’t cover it here.

The following function for the AVR will provide hardware SPI support.  The important thing to note is the RFM12 SPI speed needs to be kept within the RFM12 Specs <=2.5MHz

// pins used for the RFM12B interface

#define RFM_IRQ  2

#define SPI_SS   10

#define SPI_MOSI 11

#define SPI_MISO 12

#define SPI_SCK  13

static void spi_initialize () {

    DDRB &= ((1<<DDB2)|(1<<DDB1)|(1<<DDB0)); //spi pins on port b MOSI SCK,SS outputs     

#if F_CPU <= 10000000

    // clk/4 is ok for the RF12's SPI

    SPCR = _BV(SPE) | _BV(MSTR);

#else

    // use clk/8 (2x 1/16th) to avoid exceeding RF12's SPI specs of 2.5 MHz

    SPCR = _BV(SPE) | _BV(MSTR) | _BV(SPR0);

    SPSR |= _BV(SPI2X);

#endif

    digitalWrite(SPI_SS, 1);   // Pull SPI_SS High

}

static uint16_t rf12_xfer (uint16_t cmd) {

    // the 2 loops below each spin 4 usec with a 2 MHz SPI clock

    uint16_t reply;

    digitalWrite(SPI_SS, 0);      // SPI_SS Low

    SPDR = cmd >> 8;

    while (!(SPSR & _BV(SPIF)))

        ;

    reply = SPDR << 8;

    SPDR = cmd;

    while (!(SPSR & _BV(SPIF)))

        ;

    reply |= SPDR;

    digitalWrite(SPI_SS, 1);     // SPI_SS High

    return reply;

}

Communicating with the RFM12

Before sending any commands the the RFM12 the NSEL Pin needs to be pulled low, then pulled high when the command has been sent.

The MPU communicates with the RFM12 over the SPI by clocking 16-bit commands serially in via the SDI (MOSI) pin on the rising edge of the SCK.

The data sent to the RFM12 consist of a command code then followed by a number of parameter or data bits, this command code and parameter/data bits total 16-bits in length.

The command/data structure is then send MSB first so bit 15 is the first bit to be sent followed by bit14 and so on.  At the same time data is being clocked into the RFM12 on the SDI Pin, results (if any) are also being clocked out via the SDO (MISO) pin into the MCU MSB first, e.g. bit15 is clocked out first, then bit14 and so on.

RFM12 communicates back -NIRQ

While the NIRQ is not a required connection, it is handy for the RFM12 module to let the MPU know than an event of significance has occurred, and should be handled, instead of tying the MPU up with polling the RFM12 module to see if things have happened.

But suffice to say, the NIRQ is an interrupt generated by the RFM12 module which pulls the NIRQ pin low whenever the following occur:

• The TX register is ready to receive the next byte (RGIT)
• The FIFO has received the pre-programmed amount of bits (FFIT)
• Power-on reset (POR)
• FIFO overflow (FFOV) / TX register under run (RGUR)
• Wake-up timer timeout (WKUP)
• Negative pulse on the interrupt input pin nINT (EXT)
• Supply voltage below the pre-0programmed value is detected (LBD)

Handling the NIRQ will be covered in a future Transmitting and Receiving article.

Onto the Commands

There are 15 commands that deal with configuration, control and status of the RFM12 module.  these are listed below:

UPDATE:  Try this handy utility as you play with registers, it’s a RFM12b command  calculator  (thanks Frans, aka fotoopa, for the link!)  http://www.technofun.org/blog/2009/01/24/rfm12-rfm12b-calculator/

1) Configuration Settings Command

The configuration command as the name suggests is used to configure the RFM12  (POR denotes the Power on Reset Values)

el (bit 8): Enable internal data register.

ef (bit 7): Enable fifo mode.

The el and ef bits are used to determine how the data is moved out of the RFM module.  Most of the time you will be using FIFO mode as this simplifies things.

bits 6 – 1 (b1 – b0): This determines the band of the RFM12 module being used and needs to match the physical RFM12 module you are physically using  e.g. you don’t set the band for 433 if you are using 915Mhz module.

bits 4 – 1 (x3 – x0): Determines the load capacitance of the onboard crystal.  This allows fine tuning of the crystal frequency.  Defaults of 12.5pf should be used.

The calibration procedure uses these settings to adjust the CLK output to 10Mhz. This procedure is in the data sheet, but is pretty vague, basically hook up a frequency counter or Oscilloscope up to the CLK pin of the RFM12B module, change the Frequency of CLK to 10mhz and measure it, it it’s not at 10MHz then use the load capacitance (x3-x0) to adjust it so it reads 10MHz.  From the couple of modules I’ve tested they have all been ok at the default of 12.5pF

2) Power Management Command

The power management command controls the power to the RFM12 sub-modules, it allows you to select what circuit within the RFM12 is turned on/off.  So by disabling these circuits when not required you can control the amount power savings of the device.

The ebb, es, and ex bits are provided to optimize the TX to RX or RX to TX turnaround time as shown in the table below

This gives you an idea how the control bits are logically connected:

3) Frequency Control Command

Within each band (433, 868 or 915Mhz) we have control over what frequency the RFM12 module communicates on.  So we can have various communication links occurring at the same time on the same band, but using different frequencies, or if we are getting interference on one frequency we can switch to another clear one.

Depending on what the band is determines the resolution of the frequency steps.

The frequencies available to each band are described below in this table

The 12-bit number representing the frequency can be calculated by:

#define RF12_FREQUENCY_CALC_433(f) (((f)-430000000UL)/2500UL)  // Calculate the RFM12 register value for a given Frequency at 433MHz in 2.5khz increments

#define RF12_FREQUENCY_CALC_868(f) (((f)-860000000UL)/5000UL)    // Calculate the RFM12 register value for a given Frequency at 868MHz in 5.0Khz increments

#define RF12_FREQUENCY_CALC_915(f) (((f)-900000000UL)/7500UL)    // Calculate the RFM12 register value for a given Frequency at 915MHz in 7.5Khz increments

The 12-bit frequency value must be between 96 and 3903, if not then they will be set to these values automatically.

IMPORTANT: It is also important that you keep within your countries ISM spectrum management guidelines i.e. allowable frequencies and their use when selecting your operating frequencies.

4) Data Rate Command

This command sets the bitrate of the transmitted data or the expected bitrate of the received data.  This is the RAW physical bitrate of the module.

cs: is set if the bitrate is < 2700 bps

Here is a table I’ve prepared for common values.

If you want to calculate your own bitrates use the formula:

//calculate setting for datarates >= 2700 Baud

#define RF12_DATARATE_CALC_HIGH(baud) ((uint8_t)(344828UL/baud)-1)

//calculate setting for datarates < 2700 Baud

#define RF12_DATARATE_CALC_LOW(baud) ((uint8_t)(43104/baud)-1)

When setting bitrates you also need to take into account the receiver bandwidth settings (See  Receiver control command below)

5) Receiver Control Command

Bit 10 (P20): sets the function of INT/VDI pin on the RFM12 module, it configures it as input (Interrupt from MPU) or output (VDI Valid Data Indicator).  The VDI is the default setting.  This goes high when valid data has been detected by the RFM12 module, valid data is data that has made it past the Sync pattern.  If set as Interrupt input, we can use this to send an interrupt the RFM12.  The RFM12 will then stop what it’s doing and wait for the next command.

Bits 9-8 (d1 to d0): VDI (valid data indicator) signal response time setting:

Bits 7-5 (i2 to i0): Receiver baseband bandwidth (BW) select:

The receiver bandwidth is the amount of frequency above and below centre frequency we are receiving on (See the Frequency command for more information on changing the frequency)  that the receiver is sensitive to.  So if 400Khz is select as the Receiver bandwidth and 915Mhz is the centre frequency, then the receiver will looking for a signal anywhere +200Khz above 915 and 200Khz below, i.e. 914.800 – 915.200.

The bandwidth settings is linked to both the data rate, and Tx Modulation (Deviation)commands.  When data rate is fastest a higher bandwidth is required.   There are optimal settings for the Bandwidth and Modulation for different data rates as shown below.  Having too much bandwidth can cause a higher SNR and can cause packet corruption.  Not enough bandwidth and the incorrect signal is not received.

Incorrectly setting Bandwidth and Deviation (Modulation) is usually one of the common problems.

Table of optimal bandwidth and transmitter deviation settings for given data rates (the data sheet was a bit vague in this area and did not specify frequencies etc so I don’t know how valid they are at different frequency bands but they could be used as a starting point)

Bits 4-3 (g1 to g0): LNA gain select:

The LNA gain (Low Noise Amplifier) can be selected according to RF signal strength. It can be useful in an environment with strong interferers.  Or alternately if you have two RFM12 modules in close proximity then you can drop the sensitivity of the Low Noise Amplifier.

Well, back from a short break away (kid free woohoo!) and onto some widget builds.  I thought I’d document how I do my widget construction.  I actually find building SMD devices much easier than the PTH variety.

I have all my components in some neat snap together containers, this allows me to have everything at hand for the build.

[Click on images for larger size)

1) Solder paste is applied to the boards sparingly, ready for component placement

2) Components placed on each board, I usually do a board at a time. You will see x3 boards without any RF modules, these will be added at a later time depending on what band is required.

My SMD toaster oven setup.

The toaster oven is unmodified straight out of the box connected to the PID temperature controller.

PID Ramp controller with Solid State Relay output driver from E-Bay, that allows me to store up to 64 different temperature/time steps, each step can have their own PID parameters.  The ramp controller allows me to set and store my solder temperature profiles and when enabled will cycle through the temperature profile. 

The PID controller is installed in an external SCSI case I salvaged from an old external tape drive.

The thermocouple is a K-type with the shroud removed to give a fast response to temperature changes, I also have it wired to a spare PCB to give me a good indication of the PCB surface temperature in the oven

Rear of PID controller case, I’ve wired a power point directly a 10A solid state relay and fuse.  The SSR is driven by the PID output, so power is only applied when heat is required.  This allows me to use any unmodified toaster oven.

Batch ready for baking, carefully placed onto tray so no components are moved in the process.

All I do now is start the Temperature controller and let it do the rest (after closing the door) Since the Toaster oven is unmodified in any way I just turn it’s temperature knob to the max temperature and the same goes for it’s timer.  The bottom power light turns on when temperature controller is heating.

My hi-tech fuse and bootloader programmer ready for programming.  The headers give me good connections and allows for easy changeover.

Fuse and bootloader being programmed

As I mentioned in an earlier post, the blog and domain has been re-named to reflect more of my interests.  As a result the domain has now been fully moved across to http://blog.strobotics.com.au/ 

Please update your RSS feeds and bookmarks with the new address.  The old address is still active and will re-direct to the new domain name.

For the next version of the widget,  I’m planning to have an on board boost regulator.  This design will allows the widget to run from just about any voltage source as low as 0.7v (so NiMh will be fine) and up to 5.5v, this boost regulator in conjunction with a standard LDO regulator will give me a nice input voltage range of 0.7v – 12V.  Before I finalise the design I wanted to test things to see how well it’ll work. 

I ordered in a couple of battery holders from Polou with an integrated boost regulator, since the widgets are designed for 3.3v operation I ordered this model http://www.pololu.com/catalog/product/796,  that provides a 3.3v 100mA supply from a single AA battery, I’m not too sure what the minimum voltage is, but is running fine on a single NiMh cell.

Well today they arrived and I now have one hooked up to my solar powered widget.  Installation was simple as the small pcb on the rear of the battery holder allows me to direct access to the cell contacts, so I soldered the solar cell +ve and –ve on the respective contacts.

From some previous tests with my solar powered widget, I was finding that the batteries would start charging when the solar cell output reached around 2.8 –2.9v, this is fine for during the day with the solar cell in direct sunlight, now with the single cell I’m finding that inside under artificial light I’m charging at around 1.5v, with plenty of overhead left.

You can see below the voltage output of the boost regulator is ~3.3v (3.322 to be exact) and the voltage from my solar cell is ~1.52v, this is inside under some standard down lights while writing this post at the kitchen table (actually one of the down lights is dead so I could expect a little more output from the cell)

Just to try something different I removed the battery, seeing if the regulator could run direct from the solar cell, unfortunately it doesn’t, I doubt the cell in the current light conditions can provide enough start up current for the regulator,  I will however try it in the natural sunlight tomorrow.

With the addition of the boost regulator, and the widget in max power savings between sensor reading (when asleep widget is drawing 1.5uA, which is most of the time) then the widget should run indefinitely from the single cell….or maybe I could just get away with a solar cell and a super cap now there’s a future project….

Just thought I’d post an update on what’s happening in the widget development world.

Limited Production Run

I have a very limited number of widget kits available for purchase.  This limited batch of widget kits also include a bare prototype personality at no cost with each widget to get you started in your wireless applications.

Introductory price of $US25ea (or $20ea for 5+)  include headers, bare prototype boards, 10Mhz low profile crystal, switch, all smd components are pre-assembled and tested, latest bootloader and RFM12 test program loaded.

Options:

SMA Pigtail: $2.50 for externally mounting SMA antenna.

SMA Edge: $2.50 for mounting SMA antenna onto PCB

SMA R/A antenna 900Mhz only: $4.50 to suit SMA connectors above

CR123 Battery Holder: $2.50

I’ve yet to get full details and pictures available or a means to order online yet, so contact me in the mean time if you’re interested, please let me know the band of the RF module required when ordering, e.g 915Mhz, 868Mhz or 433Mhz.

New Bootloaders

The v1.1 of the widget bootloader for 8Mhz and 10Mhz boards are now available in the download area.  These have been updated to incorporate the onboard LEDS and provide visual indication when entering the bootloader.

Source now in SVN

All the arduino source that I’ve changed for the widgets is now in SVN on the project page.  This includes:

• Bootloader source.
• modified boards.txt that include the 8 and 10Mhz versions of the RFM12Widget. 
• Modified wiring_analog.c to read Widget battery voltage.

This can be checked out/copied directly to your arduino install directory by overwriting the existing files.  The arduino environment will need to be restarted for the boards.txt file to take effect.

V1.1 PCBs

I’ve started incorporating the user feedback into the next revision of PCBs.  Still a bit of work to be done on the PCB layouts.

Widget Mesh

Started preliminary design for a simple mesh network. 

Ultimately I would like to have the ability for the widgets to provide Zigbee type functionality (not compatibility)  along with frequency hopping as standard,  that is transparent to the application.  Only very early days so far.

The other day while playing around with the ADC on the widget I had some problems with noise causing the reading to bounce around, It needed some form filtering to remove the noise.   Normally almost everyone seems to take a number of readings and then average the result, unfortunately this takes time.

I came across this simple low pass filter on EDN.  A Low pass filter works by blocking the higher frequency (in this case noise) and allowing the low frequency signal (in this case the underlying signal) to pass. hence the name.  Perfect in cases where measuring slow moving signals, like temperature etc.  The algorithm is fast, simple to implement and works a treats.  It can be made to filter faster for a more response to change or slower to give more filtering.

#define FILTER_SHIFT 3

int32_t filter_reg;

int16_t filter_input;

int16_t filter_output;

filter_input = analogRead(0);                 // read ADC

// low pass filter to get rid of noise

filter_reg = filter_reg - (filter_reg >> FILTER_SHIFT) + filter_input; 

filter_output = filter_reg >> FILTER_SHIFT;   

The algorithm is a classified as a leaky integrator, where the latest reading have more weight than the older reading.  So you take a single reading each cycle of the sensor loop and feed that into the filter, the output is used you would normally use the raw value.

The response of the filer can be adjusted by the FILTER_SHIFT, to make it more responsive, then lower this value, to give better filtering and hence a slower response then increase this value.  For my application I found that a value of 3 to 4 worked well, but will depend on the underlying application.

I suggest you read the full article for an in depth description.

I want to deploy widgets around the home, both inside and out,  so I needed to find something that would allow some protection from the environment to the electronics, cheaply and easily.

On the weekend while doing some shopping I found the solution in the kitchen area of the local discount store, at $1.50 a piece it was the right fit for the job.  They probably won’t like U/V in the long run, but will see how they go, at that price I can replace cheaply.

(click picture for more details)

Waterproof/Dustproof housing with easy access to the internals.

This will be the standard sensor node housing.  The widget Boards and battery pack are fixed via velcro so I can easily remove for reprogramming etc. 

I still need to look at airflow of sorts for temperature, humidity and pressure sensors, will probably look at putting a couple of small vents in, this will compromise the waterproofing.  

To mount these I can put some velcro on the back and mount it on any horizontal or vertical surface.

Open and showing details of SMA pigtail connection, batteries (x2 AA side mounted) and widget board velcroed to the container (personality board removed)

Same as above, but this is for my outside sensor nodes where I’ve mounted a Solar Cell sealed on the outside, I did some initial testing and there was a filtering effect of the plastic lid and the cell, so I  decided to put the cell on the outside to get maximum efficiency, it was a pretty messy job after I used silastic to seal everything, the cell now has a smear of silicone haze across it that is appearing very difficult to remove.  So in future I think I’ll live with the slight degraded Cell performance and mount it inside, where it fits perfectly, that way I can use a couple of blobs of hot glue to fix the cell to the lid.

In my previous blog entry I described adding a solar cell to the widget and how I could measure the voltage produced by the Solar Cell, however I still need to monitor actual battery voltage easily, and preferably with not a lot of additional hardware.

Problems reading ones own voltage.

Measuring ones own voltage has a couple of problems:

1. You can’t just measure VCC directly, i.e. you can’t connect an analog pin to VCC.  The reason is the battery voltage varies, and since the default AREF is tied to VCC you will always read VCC unless you use some form of a reference not tied to VCC.

2. I can also use a reference diode and a resistor between VCC and GND, to form an external reference voltage, the diode has a known voltage drop across it so this can be measured using the default AREF.  We can calculate the battery voltage by measuring the volt drop across the diode.  While this will work, the circuit will always consume a small amount of power, even when not being used, remember I want to get as much life out of my batteries as possible.  So it rules this out as a solution.

3. For the same reasons as 1) I can’t use a simple voltage divider and the default AREF.  As the voltage varies so too will my readings.

4. I can use a simple voltage divider and the internal 1.1v bandgap reference for my AREF, the same as I used for my solar cell voltage monitor in the previous blog entry.  Again this will work, but also as in 2) this will always consume  some power even when not being used, so is ruled out as a solution in this case.

No Extra components?

We can however measure VCC voltage with no external components by simply reading the value of the internal bandgap reference voltage (1.1v) which is always fixed regardless of the battery voltage,  and by using the default AREF which is tied to VCC, so will vary as the battery voltage changes.  We now have a way of measuring the voltage change against a fixed reference.

V_BAT =  (VREF * 1024) / analogRead(14);

Where:

You might see in the above formula, that analogRead() function is reading channel 14.  But analogRead() only supports channels 0-7 right? 

Correct, but what we are doing is to read the internal ADC channels after we make a small change to the Arduino source code.

Changes to “wiring_analog.c”

To take an ADC measurement of  the internal bandgap we need to switch to ADC MUX channel 14 (23.8.1 in reference manual).   However to do this with the arduino wiring library we need to make changes to “wiring_analog.c” as per http://code.google.com/p/arduino/issues/detail?id=10.  This change allows us to read from all ADC MUX channels, internal and external.

Example

Once you’ve made the change to “wiring_analog.c” then use the following example sketch to read your VCC/Battery Voltage.

uint16_t raw_bandgap = 0;      // Internal bandgap reference

float volt_battery = 0.0;

void setup(){

  Serial.begin(57600);

}

void loop(){

  // Read Battery voltage

  analogReference(DEFAULT);                          // use VCC as AREF

  raw_bandgap = analogRead(14);                      // read and discard first result after changing reference (see 23.5.2 of manual)

  raw_bandgap = analogRead(14);                      // measure internal bandgap voltage

  volt_battery = (1.1 * 1024) / raw_bandgap;         // calculate voltage

  Serial.print(volt_battery);

  Serial.println(" v_bat");

  delay(1000);                    

}

When this method won’t work.

If you have a voltage regulator or a protection diode inline between your battery and VCC, then this will only show the voltage at VCC, not the true battery voltage. 

If you have a voltage regulator then you will always read what it puts out, and not give a true indication of battery voltage.  I guess you could still use the method as a form of low battery measurement.  i.e. when the battery falls below regulation values I guess the regulator will fail to regulate and you should get a lower than normal reading.  however I haven’t tested this theory.

If you only have a protection Diode then measure the volt drop across it and compensate in your calculations, it will still give you a good indication of battery voltage.

Update:

Some other uses for this method is for auto-calibration of sensors as described by ladyada(you need to go to the bottom of the page)

One of the tasks I want to use the widget boards for is a Wireless Sensor Network around the house for measuring environmental values.  The sensors that I want to live outdoors will need to be self sufficient in terms of power, so I wanted to see if I could charge the batteries via solar, of course this can be done, but again I want to do it as cheaply and as simply as possible, I also want the widget board to monitor the solar voltage and report it back.

I already had a 3.6v 0.2w cell that I picked up some time ago from Sure Electronics for about $10 for 5.  The spec for this cell is max voltage (under load) is 3.6v and max current is 60mA, more than enough to trickle charge x2 AA NIMH batteries. 

The Batteries should not require much of a top up as the node will be sleeping most of the time, from the power saving discussion @ JEELabs, by adding the solar, I should be able to just leave the node without having to change batteries (replacing failed batteries aside).

To measure the voltage produced by the solar cell I need a voltage divider that would produce 1.1v max @ 3.6v.

Why 1.1v I hear you ask?  The reason for the A/D full scale input voltage of 1.1V is that I’ll be using the ATMega168 internal bandgap reference as the AREF source for the onboard A/D and not the default AREF. 

There are a couple for reasons for this.  The internal bandap reference itself is a 1.1v voltage reference, because the battery voltage may change over time (remember I’m not using any onboard voltage regulators) so as the VCC / battery voltage changes, so would my A/D voltage readings unless I use a reference voltage.   Now as the reference is 1.1v this means that my input must not go above 1.1v else I will go over scale and get an incorrect reading.

I’m not going to bore you with the math so a quick calculation using an online voltage divider calculator (http://www.daycounter.com/Calculators/Voltage-Divider-Calculator.phtml)

Input Voltage = 3.6v

Output Voltage = 1.0v  (remember I don’t want to go over 1.1V so I’ve given myself some headroom)

Gave the values for R1 = 26K and R2 = 10K

Luckily I had both these values, however for the 26K I only had  one in 5% tolerance, the 10K I had as 1% (I like to use low tolerance resistors for voltage dividers so my error is minimised),upon testing the 26K resistor actually read 26.4K on my meter, so after plugging these real values in my actual FS Vout is 0.989v, pretty close to 1.0V.

A blocking diode is also required to prevent any damage to the Solar cell by the batteries, see the circuit and photo below.

(Click for larger image)

(Click for larger image and notes)

Arduino Sketch to read the voltage produced by the solar cell, next step is to find a waterproof housing and add some environmental sensors. 

Another benefit of taking voltage readings of the solar cell is I now have a light sensor.

int raw_solar = 0;        // Raw Solar FS ~ 1.0v

int raw_bandgap = 0;      // Intenal bandgap reference

float volt_solar = 0.0;

void setup(){

  Serial.begin(57600);

  analogReference(INTERNAL);  // select internal reference for AREF

}

void loop(){

  raw_solar = analogRead(0);                         // read solar voltage raw values

  volt_solar = (raw_solar * 1.1 * 3.617) / 1024;     // Scale ADC input.  (voltage divider r1= 26.4k  r2 = 10k  vi=vo/(r2/(r1+r2)) = vo/.2777 =  vo * 3.617

  Serial.print(volt_solar);                          // display raw solar voltage reading

  Serial.println("v");  

  delay(1000);                    

}

The other day when playing around with different fuse settings on the Widget Board, I incorrectly wrote the wrong values, oops one bricked board   However all is not lost.

With a second working Widget Board and a simple Arduino sketch , I used the following procedure to recover from my mishap.

First I installed the following sketch onto a working Widget Board

void setup() {

  pinMode(3, OUTPUT);  

}

void loop() {

  while(1) {

    PIND |= _BV(3);

  }

}

What this sketch does is generate a 1.2MHz clock signal on the INT1 port of the Widget Board. (Click the picture below to see the the full trace )

Next I attached this signal to the XTAL1 pin (Pin 7) of the AtMega168v on the bricked board (I just held it against the crystal pin). 

While holding this connection on the pin, I then fired up AVR-DUDE and rewrote the correct fuse settings, after confirming that the fuse values could be read back I then remove the wire and everything was back to normal.

So all is not lost

Version 1.0 of the boards is progressing to the point where I’ll be starting work on v1.1, integrating user feedback and any issues on the tracker, I’ve put a few up there so please check them out, comment or add your own.  Issue Tracker.

I’m extremely happy to say that everything has progressed really well, there are not any show stoppers with the board and as they stand are very usable.  The range of the RF with the units I’ve tested is brilliant, mainly inside, I’m hoping to do some tests over the weekend outside.

The rest of my components finally arrived yesterday and I now have fully complete boards, the low profile crystals look really slick, alas I’ve decided not to keep them in the next board revision and opted for a more generic and cheaper HC49 type crystal.   There are a few more changes, but check out the Issue Tracker.

In the Wild

A few of the extra PCB I sent out are finally arriving at their intended destinations and hopefully everyone will have time and skills to build them.  For those that have already built them I have received some great feedback.  Looking forward to their test results.

Arduino

Last night I installed the crystals on all my boards and they are now running after re-programming the fuse bits.  I’ve also re-compiled the lily pad boot loader for 8Mhz and 10Mhz along with updating the Arduino board files, I will have them online in SVN shortly.

I’m also assuming that you know how to program your fuse bits and they are correctly programmed.  The fuse values I’m using are found below in the boards.txt file. I don’t have to remind you that programming incorrect fuse values can potentially BRICK your board.  If you’re unsure please ask on the discussion group.

You need to have the correct boot loader up and running on your Strobit first.  I’ve yet to test the boot loader programming from the Arduino environment as I do all mine manually using avrdude, but here are the hex files, the 8Mhz is for if you don’t use a crystal, the 10Mhz is if you have the crystal installed.

• Strobit 8Mhz bootloader (download)
• Strobit 10Mhz bootloader (download)

Below is the boards.txt found in the Arduino hardware directory, just copy and paste into this the boards.txt and restart the Arduino environment. 

Then select the Widget Board of choice from the TOOLS|Board menu.

##############################################################

strobit1.name=Strobit Wireless Widget (10 MHz) Atmega168

strobit1.upload.protocol=stk500

strobit1.upload.maximum_size=14336

strobit1.upload.speed=19200

strobit1.boot loader.low_fuses=0xE6

strobit1.boot loader.high_fuses=0xDF

strobit1.boot loader.extended_fuses=0x00

strobit1.boot loader.path=strobit

strobit1.boot loader.file=strobitBOOT_168_10MHZ.hex

strobit1.boot loader.unlock_bits=0x3F

strobit1.boot loader.lock_bits=0x0F

strobit1.build.mcu=atmega168

strobit1.build.f_cpu=10000000L

strobit1.build.core=arduino

##############################################################

strobit.name=Strobit Wireless Widget (8 MHz) Atmega168

strobit.upload.protocol=stk500

strobit.upload.maximum_size=14336

strobit.upload.speed=19200

strobit.boot loader.low_fuses=0xE2

strobit.boot loader.high_fuses=0xDF

strobit.boot loader.extended_fuses=0x00

strobit.boot loader.path=strobit

strobit.boot loader.file=strobitBOOT_168_8MHZ.hex

strobit.boot loader.unlock_bits=0x3F

strobit.boot loader.lock_bits=0x0F

strobit.build.mcu=atmega168

strobit.build.f_cpu=8000000L

strobit.build.core=arduino

##############################################################

I’ve started to document the Wireless Widget Board in the wiki, documentation is currently all over the place, but slowly getting there.  Currently I’m working on the build instructions so those of you that I’ve sent PCBS to can at least have a parts list.  

I’ve also put up an initial bill of materials. But it would be great if someone can do a Octopart BOM and share it.

Initial building instructions can be found here: http://code.google.com/p/strobit/wiki/Rfm12BuildingInstructions with more to come.

I had a chance to grab a few photos of the progress so far, also helps that most of my components that I had on order arrived today so the boards has been kitted out with all the headers.  Now I can plug the prototype personality in, still waiting on my crystals, switches, and diodes.

This gives an idea of size. (I don’t have big hands either)  This board has a 900MHz 2dB GSM SMA antenna, prototype personality board installed and battery holder for CR123A Lithium battery. 

Different battery options, using x2AA with a switched battery pack soldered onto the board.

The SMA connector is a standard PCB straight SMA connector that has been soldered onto the edge of the board.  The board have been designed for the Sparkfun PCB edge mounted SMA connector (SKU: WRL-00593), however I found that a standard PCB SMA connector will do the same job, the distance between the centre pin and the ground pins is the same thickness as the PCB and all the pins line up with the Sparkfun footprint, the centre pin fits perfectly and so do the two bottom ground pins, only difference is the two top ground pins don’t get soldered.

One of the LEDs flashing….Its Alive!!!!

Today I did some testing on the RF side of things,  nothing scientific, just walking around the house seeing if it would dropout or report bad checksums, I’m happy to reports all is working as expected (using the 915Mhz RFM12B module)

The tests are done by using the RFM12B Example sketch found in the JeeLab RFM12B library by Jean-Claude over at Jeelab (RFM12B Arduino Library)

This library runs unmodified on the wireless widget board, just follow the instructions in the README about setting up node ids.

From the preliminary testing using some compact 1/2 wave GSM 900MHZ/1800MHZ antennas (http://www.dealextreme.com/details.dx/sku.5237)  I’m easily getting all the way around the house with no dropouts, have yet to do outside tests.